Category Archives: Hand Protection

Back Safety, Eye Protection, Fall Safety, General Safety Issues, Hand Protection, Head Protection, Hearing Protection, High Visibility Safety, Protective Clothing, Respiratory Safety

KEEPING THE CONSTRUCTION INDUSTRY SAFE (GUEST POST)

1 Comment

Construction is a notoriously dangerous industry.  In the UK, where we are based, the industry employs around five percent of the country’s workforce.  According to government statistics thosefive percent have twenty-two percent of the work related fatal injuries and ten percent of the reported major injuries.  In the US, seventeen percent of worker fatalities are in the construction industry. 

As shocking as these statistics sound, there’s been a significant improvement in both countries over the last forty years.  I think the reasons for this are threefold.  Firstly, there is much more safety legislation nowadays than formerly.  Secondly there’s a much more consistent use of safety clothing and equipment – much of which you can study at leisure on this site.  Thirdly, more workers receive various forms of safety training.  I firmly believe that the way to continue to improve safety in construction is to make training and refresher courses widely available for people employed in the industry and I also think that it’s in the construction companies’ best interest to ensure that their employees can access training.  Why do I believe this?  Well, there are several reasons: 

1)      Companies can be financially liable for the safety of their employees.  Even with insurance your premiums will go up dramatically if you have accidents on your sites.

2)      Companies generally want to employ the best workers.  If you have a good reputation for safety practice, people are more likely to want to join you and stay with you.  If your employees see that you’re willing to develop their skills, they’re much more likely to stay loyal to you.

3)      Workers are often injured by the actions of other workers.  Think about it – how likely is it that you’ll be fatally injured by a falling object that you’ve dropped? How likely is it that you’ll have put up the scaffolding that’s worked loose and caused you to fall?  The more workers on your site who have safety training, the safer the whole site will be.

4)      Companies can receive site inspections from official bodies.  Some are empowered to fine companies for non-compliance with legislation.  The more knowledgeable your employees are, the less likely you are to have compliance breaches on your sites.

5)      Companies are in a position to request bespoke training from education co-ordinators if they’re putting through a large number of pupils.  This means that the trainer(s) will put your company’s policies and procedures at the heart of their training.  You are also in a position to monitor the way that the training is delivered and make sure that your employees have the skills rather than just the piece of paper at the end of it. 

Are you involved with the construction industry?  Do you have any views on the safety training  you’ve received?  We’d be interested to read your responses in the comments section.

 Sent to us by Carl, of blogginghelper.co.uk
Email: carl@blogginghelper.co.uk
Twitter: @blogginghelper
Web: www.blogginghelper.co.uk

Eye Protection, First Aid Safety, General Safety Issues, Hand Protection, Head Protection

HOT WORKS – SAFE WELDING OPERATIONS (GUEST POST)

1 Comment

Sent by Jason of riskatmedia.com 

There are particular hazards associated with hot works, which includes welding activities, the use of oxy/gas equipment and acetylene, cutting operations and air-arc gouging. Each year over 1000 work related injuries to welders are reported to the Health and Safety Executive in the United Kingdom.  Approximately 300 of these are major injuries, such as amputations and fractures.  Some of these injuries result from hazards that accompany almost all types of work activity, such as handling, slips and trips and being hit by a moving or falling object.  Others are more likely to be solely associated with welding activities, such as the intensity of electric arcs and high temperatures. 

Manual handling

Prior to carrying out any unavoidable manual handling activity, you should help to protect yourself from injury by following good manual handling practices. Consider the task to be carried out and the nature of the load, and be aware of your own capabilities and the environment in which you are working. In particular, portable welding equipment, gas cylinders and work pieces can be extremely heavy and you should give consideration to safe manual handling practices before undertaking any job that involves lifting these items. 

Slips, trips and falls

Slips and trips can result from contamination, obstacles, inappropriate footwear, reduced visibility, the environment and people’s attitudes. Good housekeeping can significantly reduce the risk of serious slip and trip injuries. Containing spent rod ends and removing debris, slag, packaging and other waste materials to waste skips. You can also reduce the risk of slips and trips by properly routing any cables or air hoses that you use.

A safe place of work should be established to take into account the restricted visibility resulting from welders wearing protective head-shields. Consider whether the environment in which you will be working increases the risk of slips and trips and take responsibility for your own and your colleagues safety by appropriately containing any spills that you might discover. 

Moving or falling objects

Death or injury can result when large and heavy objects, such as gas cylinders used during welding operations, tip or fall because they have not been properly secured. Gas cylinders should always be secured by means of a chain, strap or cable to a building support, or proper cylinder cart. Bottle trolleys should also be covered when gas cylinders are moved short distances. 

Electrical Dangers

Electric shock from welding equipment can result in death or severe burns. Serious injury can result if the welder falls as a result of the shock. To prevent the risks posed by electrical hazards, all equipment should be tested and certified before use. Air pipe work should be checked to ensure that there is no electrical conductivity between the ends and the welding return cable should be connected as close as possible to the work piece. The electro-magnetic field produced by certain types of welding equipment may pose a risk to welders who have implantable medical devices fitted. Please make sure that you have informed your supervisor if you have an active implantable medical device, and talk to your doctor about the safety of using welding equipment in relation to your medical device. 

Fire and Explosion

Welding and allied processes produce molten metal, sparks, slag and hot work surfaces which pose a risk of fire and explosion, and which can result in fatalities, serious injury and plant damage. Flying sparks are the main cause of fire and explosion, especially as sparks can travel up to 10 metres from the work space. Sparks and molten metal can travel even greater distances when falling and can pass through and become lodged in cracks, clothing, pipe holes and other small openings. To reduce the risk of fire and explosion when carrying out Hot Works, a permit for work should be obtained before commencing work on any operational plant. Working areas and the areas below them should be kept free of combustible material. Fixed items of plant, such as installed electrical cables should be protected by a fire blanket. Sparks should be contained by means of a non-flammable material. Fire extinguishers should be close at hand, and the working area should be inspected when work is suspended to ensure there is no residual risk of fire or explosion. 

Oxy-Gas Equipment

Additional precautions are necessary when working with oxy-gas equipment. Gas bottles should be in an upright position, secured to prevent falling and located in an open aspect during use. The cylinder valves should be kept shut while hoses and equipment are being connected or disconnected. The requirement to fit flash back arrestors to both hoses is mandatory, but you should also ensure that you have enough gas in both cylinders to complete the job and that you follow the manufacturer’s guidelines for proper shut-down and start-up procedures for the equipment you are using to reduce the risk of flashbacks. The bottle key should be kept on the valves while equipment is in use to enable quick shut off in the event of an emergency. A fire watch should be maintained during operations.

All gas cylinders should be isolated when not in use to prevent oxygen or gas enrichment. And all operators should subject oxy-gas equipment to daily pre-use checks, such as leak detector spray or pressure drop tests. Contamination of gas cylinders by oil or grease should be avoided, as this may increase the risk of fire and explosion. Direct exposure to fire can initiate a heat generating decomposition reaction within acetylene gas leading to the potential for explosion. Any cylinders exposed to a fire should therefore be isolated for at least 48 hours, or until deemed safe. When not in use, gas cylinders should be stored in properly constructed and ventilated cages, with no source of ignition within three metres. 

Eye damage and burns

Most welding and related activities produce significant quantities of non-ionising radiation, such as visible light, ultraviolet and infra-red, which can cause eye damage and painful skin burns. The intensity and wavelength of energy produced depends on the process, welding parameters, electrode and base metal composition, fluxes, and any coatings or plating on the base material. Ultraviolet radiation increases approximately as the square of the welding current. Visible brightness or luminance of the arc increases at a much lower rate. Processes using argon produce larger amounts of ultraviolet radiation than those using most other shielding gases. The risk of injury to the operator resulting from exposure to non-ionising radiation can be reduced by decreasing the length of exposure, wearing a head shield and standard Personal Protective Equipment or PPE with gauntlets and Proban fire-retardant overalls. 

Welding Fumes

Many welding processes produce fumes which are potentially harmful. Depending on the materials involved, the ill effects can include irritation of the eyes, skin and respiratory system, or more severe complications such as impairment of speech and movement. Symptoms of over-exposure to welding fumes may manifest immediately or some considerable time later. To reduce these risks, position the work area with an open aspect to minimise fume concentrations. Use forced ventilation where necessary and, in confined spaces, an air fed hood. Use a disposable mask appropriate to the type of fumes produced during work operations, and remember that respirators are mandatory for stainless steel welding. It is also important to refer to the relevant Hazardous Material Assessment which will outline additional safe working practices for the materials used. 

Work piece Stability

Where cutting operations are performed, it is always important to give consideration to the effect that these operations will have on the stability of the work piece. In particular, consideration should be given to weight distribution, as the removal of significant weights may alter the balance of the work piece. Where appropriate, the work piece should be supported. You should also plan how items that have been removed will be lowered without risk to yourself, to others who may be working nearby, or to equipment. 

Emergency procedures

In the event of an emergency, conduct an initial assessment of the situation. If you believe that the situation is beyond your control, evacuate the area immediately. Turn off all valves, but only if it is safe to do so. If the flame from a leak cannot be extinguished by turning off the valve, do not stay and attempt to fight the fire. Evacuate the area immediately. 

Guest post Riskatmedia Safety Training Videos

Eye Protection, General Safety Issues, Hand Protection

PROTECTING YOUR MOST IMPORTANT TOOLS – YOUR HANDS (GUEST POST)

1 Comment

 We all have a favorite tool, maybe it is that new Lithium-Ion powered cordless drill, it might be a new air compressor for powering all of your pneumatic tools, or it might be an old set of wrenches that you’ve had since you were a teenager and bought your first car.  But no matter what your favorite tool is and what tools you use each day to make a living, you have to invest in the right pair of gloves to protect your most important tools- your hands.

Chances are that if you work for a large company, there are regulations and programs put in place by the safety coordinator or safety manager.  Depending on what kind of job you do, you might use many different types of gloves to protect your hands.  If you work for a smaller company or are a DIY’er, you may not have any expertise on the subject or mandated regulations.  It is up to you to protect yourself.

Like any other type of safety gear, hand protection come in all shapes and sizes and are often specific to what type of job is at hand.  Depending on what type of job you are doing will determine the proper glove for the task.  Gloves will be divided into different categories such as cut resistant, chemical resistant, insulated, arc protection, high temperature, general purpose and many specialized gloves.  The most important thing to remember is that you must use the correct glove for the job and you should have a basic understanding of why that glove is the right choice, not just because somebody told you to wear it.

1.        Cut Resistant.  Cut resistant doesn’t mean cut proof.  There are many degrees of protection, depending on what glove you chose.  Most of the cut resistant gloves will be a mix of material, usually coated on the palm with extra protection such as Nitrile or Polyethylene.  They may be cloth mixed with rubber or Kevlar.  These gloves are going to be used for handling parts with sharp or pointed edges such as sheet metal of glass or tile.  They will be puncture resistant and protect your hands from cuts and scrapes. 

2.       Chemical Resistant.  Usually made of rubber, Nitrile or PVC, chemical resisatnat gloves are going to protect the worker form harmful chemicals.  They are often longer cuffed gloves, protecting past the wrist and can even be elbow or shoulder length depending on the required needs.  They are going to protect against oil, grease, acids, alcohol and solvents.  They are used in mining, utilities, manufacturing and the automotive industries.

3.       Insulated.  These gloves are going to protect from electric shock and are very important for the safety of lineman, electrical utilities and electrical workers.  It is very important to verify voltage protection and to inspect for cracks and tears before each use.  These will be very specific to a job and most people will never need this type of glove.

4.       Arc Protection.  Arc protection gloves are going to be made of Kevlar and Nitrile.  They are going to be cut and flame resistant and are used in facility work, machinery work, and heavy equipment service and cable installation.

5.       High Temperature.  High temperature gloves are exactly what they appear to be, they are going to protect the worker from being burned.  These gloves will protect form burns and high temperatures, usually with a cotton or Nitrile blend.  They are used in production of glass and plastics, foundry operations, steel mills and in the automotive industry.

6.       Disposable Gloves.  Latex and Nitrile disposable gloves fit into this category.  They may be used in laboratory, medical and janitorial applications.  They are good for protection, but are thin and allow for greater dexterity.

7.       General Purpose.  This is a broad category; it is going to include any of the gloves that you may use in a job that isn’t inherently dangerous, such as yard work, driving, working around the house.  These are gloves to protect from blisters, splinters and other common problems on the job. 

There is a glove for just about any job that needs to get done.  Workers are injured every day because they are not wearing the proper hand protection and it is often left to the individual using the glove to decide what is appropriate for the job.  Just like you would always put on a pair of safety glasses to protect against eye injury, hand protection should be available at all times and in every tool box.

Bio: Jay Preston is author and Brand Manager for ToolHQ, Australia’s premiere cordless tool source.

Thanks, Jay for this thorough explanation of the types of gloves.  For anyone who wants to protect their hands, depending on the right glove for the job, check Texas America Safety Company for just the right type.

General Safety Issues, Hand Protection

TOP SEVEN ESSENTIAL TRAVEL SAFETY TIPS FOR SENIOR CITIZENS (GUEST POST)

2 Comments

By Rebecca Jones

Traveling is a phenomenon which can act as a great stress buster and provide an enjoyable experience to nurture for life. While traveling is a great experience in itself, senior citizens and older people must make sure that they are covering all aspects of travel and safety before embarking on any tour. Here are the top seven tips that can bring an added sense of security in the traveling plans of senior citizens that can help enjoy their trip without any mental worries in case of any emergencies.  

Health Checkup before Travel: Getting a proper health checkup is recommended for all travelers especially senior citizens to avoid any hassles while traveling. Before embarking on your journey, consult your physician for all wide-ranging medical investigations including any pre existing diseases or old age related potential diseases that may occur. Senior citizens are advised to check with their physicians about potential change of dietary habits while traveling depending on the area of travel as diet has a direct impact on health aspects of senior citizens. If you are traveling to a tropical country it is advises to avoid regular water and opt for bottled water to avoid any water borne diseases that can impact the stomach and hurt potential travel plans.  
 
Carry Adequate Medication: It is advised to carry adequate medication before embarking on any travel or tour. As a safety measure it is helpful to carry medication with a cushion of an extra week to ten days to avoid any shortages due to emergency situations or potential extension of the trip due to any reason. Also medications are pretty unique for each country and all medications may not be as freely available in foreign nations. Apart from carrying disease specific medicines, it is advised to carry general purpose medication that can be useful in case of an unwanted emergency. Taking hand sanitizer along can help when water for washing hands isn’t available.  Germs abound on planes, elevator buttons, etc. Senior citizens traveling to cold countries are also recommended to carry an extra protection of clothing to avoid any cold related diseases that affect the children and older people much more than young adults.  
 
Get Travel Insurance: Getting travel insurance is one of the most useful tips for all travelers’ especially senior citizens. Getting a travel insurance not only adds a comfort level mentally to the immediate family but also allows a peaceful journey knowing that the worst case scenarios are fully protected. While most people consider travel insurance as an unwanted expenses, it is a wonderful protective tool that must be incorporated in all travel plans to avoid any untoward incident while traveling be it while flying across various airlines or traveling locally in foreign countries. With many tourist specific places usually also have a high rate of crime, it is an essential tool for the older people to counter any bad situation.  
 
Carry Medical Prescription for Pre Existing Diseases: All senior citizens must carry their original medical prescriptions for any existing diseases to help them avail medical help in case of an emergency. If god forbid any health issues occur during travel, local doctors or local physicians can understand the case history and the pre existing diseases and the current medications being taken by the person to quickly diagnose any medical problems. Also medical prescriptions an make sure that one can procure medications from any chemist store across the world which cuts out the risk of running out of medications being carried in person.  
 
Update Information on Mobile Networks: Mobile phones are a marvelous helpful tool for tourists especially the senior citizens. A mobile phone can make sure that a senior is connected to his immediate family and loved ones at all times. It is recommended to check the availability of mobile networks in the area one is traveling to. Also while traveling to foreign countries, a tour guide must be involved which can have a local contact number for the family to contact to in case of an emergency of networks of the old age traveler not working in alien conditions or foreign countries. Updating as much information for mobile networks, availability of local mobile numbers or other contact numbers must be shared with the folks back home to avoid any communication gap in case of any untoward incident.  
 
Travel in a Group: Older people are advised to plan their travel in group which can have immense benefits. While at the one hand, traveling in a group of known people is much more enjoyable and fun, it also makes sure that there are people to take care of the individual in case of any medical or local emergency. Traveling in a group also allows for far better discount rates on various travel itineraries plus providing a comfortable cushion of having people with the same understanding around the seniors at all times.  
 
Avoid Hectic Itinerary: Prevention is better than cure it is said. The saying is much more apt for older travelers and senior citizens. Traveling can be a hectic experience both mentally and physically. While young adults may have no problems in planning a hectic travel plan, older people must make sure that they cater for adequate rest between travels especially after long flights to avoid any travel related tiredness that can be potentially fatal in some cases. Traveling a travel schedule must cater for rest days between travel even if that means adding a couple of more days in the overall itinerary. Also senior citizens must avoid hectic adventure activities while traveling so that they remain safe and secure at all times. 

About the author: Rebecca is a blogger by profession. She loves writing, reading and travelling. Besides this she is fond of luxury cars and wishes to own a Bugatti Veyron 16.4 one day.

Eye Protection, Fall Safety, General Safety Issues, Hand Protection, Head Protection, Hearing Protection, High Visibility Safety, Protective Clothing, Respiratory Safety

WHAT SHOULD I INCLUDE IN MY CONSTRUCTION SITE SAFETY INDUCTION? (GUEST POST)

2 Comments

Sent by Jason of riskatmedia 

Every week at least one construction worker will die as a result of work-related injuries.  Most of these fatalities involve skilled construction and building workers. Falling from a height is the greatest single cause of fatal injury, followed by being struck by a moving or falling object, contact with electricity, being trapped by something collapsing or overturning and being struck by a moving vehicle. In addition to this, over 3500 construction workers suffer major work-related injuries every year.

There are many dangers involved in working on any construction site.  These hazards are real and often potentially life threatening, but we face them every day and sometimes forget how real and close they may be to all of us. This blog will cover most of the topics required for a Construction Site Induction.

Site Access

Access onto site should always be controlled for safety and security reasons.  This may be by means of a signing in and out procedure, or by means of controlled entry technology.  It is important that you use controlled entry procedures every time you enter or exit the site, this will allow management/security to determine exactly who is on site should an emergency situation arise. 

Personal Protective Equipment – PPE

Personal protective equipment, or PPE, is an important means of reducing the hazards associated with work on a construction site.  The minimum PPE that should be worn on site is a hard hat, appropriate gloves, safety footwear and a high visibility vest or jacket.  This PPE should be worn on site at all times and may be supplemented by additional PPE, such as eye protection, ear defenders, dust masks and a safety harness, as stipulated in your risk assessment and method statement or permit to work.  All items of PPE need to provide a good fit and be in good working condition, so it is important to check your PPE before you use it.  PPE should be stored in a secure, clean and dry environment and any contaminated PPE should be removed carefully, cleaned or disposed of in a safe manner.” 

Alcohol, Drugs and Medical Conditions

It is extremely important that you never come to work in possession of, or impaired by alcohol or drugs. These substances expose everyone on site to risks that are unnecessary and easily avoided. If you have a medical condition, have an active implantable medical device fitted or use prescribed or other medicines, you should report this to your manager/supervisor so that the details can be recorded for use in the event of an emergency.  Any information that you provide should be treated in the strictest confidence. 

Traffic Management and Pedestrian Walkways

Construction sites are busy and noisy environments with mobile plant and vehicles often in close proximity to pedestrians.  For these reasons, designated pedestrian walkways and Egress Routes should been marked out on the site. Stick to these walkways whilst on site and don’t be tempted to take short cuts that might expose you to unnecessary risk.  If you drive on to site, make sure that you stick to the speed limit, that you only park in designated parking bays and that you keep footpaths, access routes and pedestrian walkways clear.  A copy of the most up to date traffic management plan may be displayed on site notice boards, along with other important safety information. 

Welfare Facilities

Welfare facilities should be available on site and may include toilets, a restroom, a washroom and drying room and may include a canteen.  Use these facilities responsibly by helping to keep them clean and tidy and recycling your waste as appropriate. 

Vermin

Vermin are encouraged by the presence of food on site, so it is very important that you only eat in designated areas, that you dispose of food waste appropriately and that you do not take any food on to site.  Vermin, such as rats, can spread diseases, including the serious and possibly fatal disease Leptospirosis. 

Smoking, Music and Mobile Phones

Smoking and music are generally not permitted on construction sites, except in areas designated by site management.  Mobile phones should only be used in lower risk areas, such as offices and welfare facilities, where you are safe and unlikely to affect other workers or operations.  Mobile plant operators and drivers of site vehicles must never use a mobile phone whilst operating or driving. 

Hazardous Substances and Materials

During your work you may use or come into contact with substances such as adhesives, paints or dust, which may harm you or the environment.  If you use these hazardous substances you are required to understand the precautions that must be observed and the PPE that must be used, when transferring, mixing or using these substances.  You are also required to understand the relevant storage, disposal and emergency arrangements.  Information on the substance as well as an assessment of the hazards associated with its use should also be made available.

Any spills of fuels, oils or potentially hazardous substances, should be immediately contained using the appropriate spill kit and then reported to the supervisor or manager so the spill can be safely cleaned up. 

Shots relevant to environmental management

To help reduce the effect of operations on the environment:

  • Reuse and recycle as many materials as possible
  • Compress waste and use waste segregation facilities where possible
  • Dispose of waste responsibly and in accordance with legislation
  • Damp down to minimise dust
  • Turn off any plant or equipment not in use
  • Ensure plant and equipment are well maintained
  • Only use task lighting where necessary
  • Turn off any taps and hoses when not in use and report any leaks 
  • Never pump or pour anything down the drains and only wash down plant and equipment such as cement mixers in the areas provided
  • Where there are trees that need to be protected, please remain within designated work areas and avoid damaging tree routes
  • Do not disturb nesting birds, newts, badgers, bats or invasive weeds
  • Be aware of any habitats or historical remains on site. 

Emergency Fire Procedures

Specific emergency procedures should be followed in the event of a fire.  If a fire occurs, an alarm will sound.  If you hear a fire alarm, stop what you are doing.  Isolate any plant or equipment that you have been using and make your work area safe.  Take the nearest escape route and follow a safe route to the nearest assembly point.  Remain at your assembly point until you are given the all clear to return to work.  Take the time to familiarise yourself with the specific emergency procedures that apply to the site, as well as the location of the assembly points. 

Flammable Materials

To help prevent fires, flammable and combustible material should always be stored safely.  Gas bottles should be stored in secure, vented cages or stores with appropriate warning notices.  When working with gas, always ensure that you do so with adequate ventilation well away from any naked flames. 

Accident Procedures

Construction site rules and procedures are designed to minimise the risks to the safety of everyone who works on site.  But accidents may still happen.   In the event of an accident, first aid facilities should be available on site.  The names of all trained first aiders may be displayed on the site information board.  If you are involved in an accident or a near miss, no matter how minor, please report it to the site management so that they can ensure you get the correct medical treatment and take steps to prevent the incident from recurring.  If you witness a serious accident, get help and send someone for the site manager.  Try not to move the injured person, but do make sure that they are safe. 

Slips, Trips and Falls

Good workmanship and good housekeeping are practices that can help to prevent accidents and fires.  Remember to route power and lighting cables so that they do not pose a potential trip hazard.  Tools, materials and equipment should only be stored where indicated and should be stacked safely.  All access routes and walkways should be kept clear of obstructions, especially those that are used by members of the public including children.  Tidy and clean your work space throughout the day and never leave tools, equipment or materials where they could create a trip hazard. 

Electrical Safety

All items of electrical plant used on site should carry a valid testing certificate or label to ensure Electrical Safety.  If an item of plant does not carry a valid electrical testing label, is damaged or has a missing guard, then please, do not use it.  If you use battery powered tools ensure that batteries are charged in a safe area and do not obstruct welfare facilities or create trip hazards. 

Tower and Mobile Cranes

Tower and mobile cranes may be in use on site, so it is important that you do not enter unloading areas unless you are authorised to do so.  You should also be aware of the fact that plant including cranes, telehandlers and powered access equipment should only be operated by individuals who are suitably trained and authorised to do so.  If you are trained and authorised to operate plant, make sure that you carry out daily pre-use safety checks, that all safety devices and locking pins are in place, that the flashing beacon and any warning devices are working and that all-round visibility aids are in place and effective.  Seek the assistance of a banks-man where visibility is limited and never leave the keys in an unattended machine. 

Work Equipment

Whatever work activity you are carrying out on site you will be using work equipment. Only use the correct tools for the job and only use tools and other work equipment which you have been trained to use. 

Risk Assessment, Method Statement, and Permit to Work

Before you undertake any job, make sure that your supervisor has briefed you, that you have a complete and valid risk assessment and that you are able to and do work according to your method statement.  Be aware that new risk assessments and method statements may be required where jobs have changed or where new hazards have been introduced.  In addition, certain work on site may require a permit or permission to work. These are issued after you have submitted a risk assessment and method statement for a particular job.  If you are unsure whether a particular job requires a permit, ask your supervisor or manager. 

Working at Height

You may remember that falls from height represent the single largest cause of death in the construction industry so Safe Working at Height is essential. It is therefore extremely important that you follow safe working practices when work at height cannot be avoided.  Always use an appropriate working platform or work equipment whenever there is a potential to fall, which includes loading and unloading of vehicles.    Always check your work platform before use, and be especially vigilant in windy, wet or icy weather.  Remember, the use of a harness requires extra competence and is a last resort.  If you operate powered access equipment you must have the appropriate training, certification and authorisation for that particular type of equipment.  You should also carry out and record a daily pre-use inspection.  Ensure that the access equipment is only used on stable ground, that it is not used in high winds, and never use it to lift or transport loads. In a boom type mobile elevated work platform you must wear a full body restraint harness secured to an anchor point by a suitable length, work restraint lanyard. Remember to park the mobile access equipment safely and to remove the key when the machine is not in use.  The use of ladders and stepladders is discouraged and may be permitted only where the task is simple, of short duration, and no safer alternative is possible.  Scaffolding, access ladders and mobile towers may only be erected, dismantled or modified by trained and competent persons.  Remember to lock the wheels and fit the guard rails and to check that the scaff tag is in date and valid. Close all loading bay gates after use and never load materials onto guard rails. 

Excavations and Quick Hitches

Safe working practices are essential when excavating.  Check and mark the location of services, protect services with barriers or road plates, dig trial holes to confirm location and depth and avoid the use of mechanical equipment, picks and forks around pipes and cables.  Don’t enter an excavation unless you have to.  If you do enter an excavation, make sure that the sides are battered, stepped or supported, use a ladder to gain access and put barriers around the edges if there is a potential to fall.

Buckets can become detached from excavators during operations if the appropriate locking pin or device is not properly fitted.  The excavator operator must ensure that the locking pin or device is correctly engaged and secure before commencing operations. 

Manual Handling

Workers in the construction industry suffer considerably higher rates of manual handling related injuries than workers in any other industry.  Help to protect yourself from injury by following good principles of manual handling.  If you must lift a load, assess whether you can lift it alone or whether you need someone to help you.  Remember to consider the environment in which you are working.  Always adopt the correct lifting technique. 

Your Health

Your health is as important as your safety.  Vibration white finger and dermatitis are too often suffered by construction workers.  Protect against these painful conditions by reducing your daily exposure to vibration, wearing the correct PPE and using barrier creams to protect yourself from contact with potential skin irritants such as cement.  Remember to apply sun cream if you are going to be working in direct sunlight. Wear an appropriate dust mask and use vacuums rather than sweeping to clear dust.  Check your tetanus vaccinations are up to date. Never touch discarded needles or syringes.  Stop work and clear any area if you discover a substance you think might be asbestos.  If you discover asbestos or discarded needles, please report this to site management. 

Riskatmedia – Safety Videos

Ergonomics, Eye Protection, Fall Safety, First Aid Safety, Hand Protection, Hearing Protection

POWER TOOL SAFETY (GUEST POST)

1 Comment

By Jason, from RiskAtMedia: 

All work activities carry the potential to cause harm to our own and others’ health and well-being, but we sometimes forget how real and close to us these hazards are.  Every year, a large number of people are killed at work, and an even greater number of people suffer work related injuries because they are unable to follow safe working practices. There are particular hazards associated with the use of powered tools, some of these hazards accompany almost all types of work activity, such as manual handling and slips and trips.  Others are of particular concern to powered tool operators and we will consider these in this Power Tool Safety brief. 

Manual Handling

Manual handling related activities are a major cause of occupational injury.  Low back pain, joint injuries and repetitive strain injuries of various sorts, affect over a million people each year, and many of these injuries are the result of manual handling. Prior to carrying out any unavoidable manual handling activity you should help to protect yourself from injury by following good manual handling practices.  Consider the task to be carried out and the nature of the load, and be aware of your own capabilities and the environment in which you are working. In particular, tools and work pieces can be extremely heavy and you should give consideration to safe manual handling practices before undertaking any job that involves lifting these items. 

Slips, Trips and Falls

Slips, trips and falls represent a significant cause of work related injury.  Slips and trips can result from contamination, obstacles, inappropriate footwear, reduced visibility, the environment and people’s attitudes.  Good workmanship and good housekeeping are practices that can help to prevent accidents and fires.  By removing debris, swarf, packaging and other waste materials to waste skips you can contribute significantly to good housekeeping.  You can also reduce the risk of slips and trips by properly routing any cables or air hoses that you use, by appropriately storing materials, tools and other equipment and keeping walkways clear, by ensuring that you always wear appropriate shoes and by taking responsibility for your own and your colleagues safety and appropriately containing any spills that you might discover. 

Contact Risk

Contact with moving or rotating power tools is a significant hazard to personnel using power tools, as well as to personnel working close by, and can result in serious injury.  All personnel need appropriate training and experience to be able to use work equipment safely.  Never use any work equipment unless you have received suitable training and are qualified and competent to do so.  Before you begin to use a powered tool, make sure that you have read the manufacturer’s instructions for use.  Study the tool to make sure that you know which parts of the tool move, which parts are stationary and which parts are sharp.  Make sure that all guards are in place.  Where appropriate, remember to securely clamp tools or work pieces.  And ensure that you only use tools for the job they were intended to perform, as this can significantly reduce the risk of injury.  To protect others from the risk of contact with the moving or rotating powered tool parts, make sure any necessary warning signs and barriers are in place before you begin work.  You should also take care if you need to walk through or work in an area adjacent to where another person is using powered tools. 

Electrical Safety

Electric shock from powered tools can result in death or severe burns.  Additionally, serious injury can result if the operator falls against a powered tool as a result of the shock.  To prevent the risks posed by electrical hazards, all electric powered tools should carry a valid test certificate or label.  Testing should be carried out by suitably trained individuals.   If an electric powered tool does not carry a valid test label, it should not be used and you should inform your supervisor. 

Malfunction

You should also carry out a visual pre-use inspection of all tools to ensure that they remain undamaged.  If you do discover a defect, please do not use the tool and report the problem to your supervisor.  Never attempt to make temporary repairs to a tool.   You should also observe the tool while it is in use for possible signs of malfunction.  If you notice that the tool is vibrating abnormally, doesn’t sound right, or is displaying signs of any other problem, switch it off and report to your supervisor.  When using an impact wrench, only sockets specifically designed for use with impact wrenches should be used and you should carry out a daily pre-use inspection of the socket to ensure that it is undamaged.  Never use sockets designed for hand ratchets on an impact wrench. 

Maintenance

Ensuring that equipment is appropriately cleaned and maintained is also central to safety.  Clean tools after each use, as a dirty tool is unsafe and is difficult to use.  When you carry out maintenance, make sure that the equipment is isolated and cannot be turned on accidentally.  Ensure swarf has cooled before using gloves and a brush to remove it and clean the tool.  If you need to remove swarf from a running powered tool to prevent long strands developing, make sure that you are not wearing gloves and use a rod to remove the swarf.  Never use a rag to clean a tool while it is running and never use compressed air to clean a tool. 

Entanglement

When using powered tools, wear close fitting garments, do not wear a tie or jewellery and tie back long hair and long beards to reduce the risk of entanglement. 

Personal Protective Equipment PPE

Personal Protective Equipment, or PPE, is an important means of reducing the risks associated with projectile particles produced when using powered tools.  At least standard PPE with safety glasses should be worn.  It may be necessary to screen the work area if projectile particles pose a hazard to individuals working or passing nearby.  Only PPE in good working condition will reduce the hazards associated with your work, so it is important to remove, clean and store your PPE correctly. 

Noise at Work

Hearing loss caused by exposure to noise at work is a significant source of occupational disease, with many people suffering deafness, tinnitus or other ear conditions as a result of exposure to excessive noise levels at work.  The level of noise and how long people are exposed to noise at work both contribute to potential hearing damage.  Noise can be reduced to harmless levels by wearing industiral ear plugs and ear defenders. These items of PPE should therefore always be worn while using impact wrenches, and should also be worn when using other powered tools unless local measurements indicate that noise levels are below the level at which such action is necessary. Controls should also be considered for individuals working in close proximity. 

Human Factors

Human factors also play a role in increasing the risk of injury while using powered tools.  Never come to work in possession of, or under the influence of, alcohol or drugs.  These substances expose everyone to risks that are unnecessary and easily avoided.  You should also not use powered tools if you are overly tired or unwell, as concentration is important to using tools safely. 

Hand Arm Vibration Syndrome HAVS

If you regularly use powered tools, you may be at risk of developing Hand Arm Vibration Syndrome or HAVS.  This condition involves damage to the blood vessels, nerves and joints of the hand, wrist and arm.  It is a painful and debilitating condition, resulting in numbness of the hands to the extent where it is impossible to feel with your fingers and very difficult for you to pick up small objects.  This can make both occupational and leisure activities, such as playing darts, fishing or DIY, impossible.  HAVS is entirely preventable.  Always use the right tool for the job, as this will allow you to complete the job more quickly and will expose you to less hand-arm vibration.  Carry out a pre-use inspection of all hand held equipment and report any damage to your supervisor, as faults and general wear may result in increased vibration.  If you do experience abnormal vibration from hand held equipment, please report this immediately.  Try to reduce the amount of vibration you are exposed to in one go by doing other jobs in between.  Use a relaxed grip and avoid using excessive force on a tool or work piece.  Store tools so that they do not have very cold handles when used next.  Keep your hands warm and dry and take breaks to exercise your fingers regularly.   Wear gloves when using impact wrenches to reduce the effect of vibration. 

Compressed Air

Compressed air is a safe and reliable alternative to electricity for powering impact wrenches and other air powered tools, but it can be dangerous if it is not used responsibly.  In particular, contact with streams of compressed air can penetrate the skin and enter the bloodstream.  All compressed air plant should be appropriately inspected and certified to ensure that it is safe to use.  Never operate air compressors at faster speeds than the manufacturer’s recommendation and ensure that the air intake is from a clean, outside and fresh air source, with screens and filters used to clean the air if necessary.  Unless your tool has a quick disconnect plug, you should always turn off the air supply at the control valve and bleed the tool before disconnecting.  You should never compress, bend or kink air hoses and you should never carry an impact wrench or other tool by the air hose.  And never use compressed air to clean your clothes or yourself. 

Emergency Procedures

In the event of an emergency, isolate any equipment that you have been using and evacuate the area according to the site emergency procedures.  If you are involved in an accident, seek immediate assistance. 

Riskatmedia – Safety Videos

Eye Protection, General Safety Issues, Hand Protection, Protective Clothing

METALWORK: CUTTING OUT THE DANGERS (GUEST POST)

The market for welding equipment and profile cutters has broadened considerably in recent years as such machinery become more affordable, less cumbersome and thus available to the majority of the population. The hazardous methods used to accurately carve shapes from metal sheets are now adopted equally by unskilled hobbyists working in their own home and heavy industries of mass production. The widespread availability and unregulated use of profile cutting machinery has exposed more people to harm. Looking at plasma cutting in particular, it is easy to see the dangers of this trade and the necessity of certain safety precautions which all users must adhere to. 

The Risks 

From arc-eye to smouldering debris on the skin, the dangers associated with plasma cutting are all extremely hazardous to anybody working in the vicinity. One serious risk is the fire hazard created by the arc of plasma which not only emits intense heat but also gives off sparks, which can land on nearby surfaces, clothing or skin. The arc also produces a bright glare which is damaging to the eyes. Molten metal and shards of freshly cut debris can be airborne and can burn or cut exposed skin. Then there are the fumes released by the metal during the process which can create an immediate choking hazard or more long term health problems. Any coating on the metal (ie. galvanised steel) must be removed beforehand as they produce truly toxic fumes. Finally, the extreme power output of a plasma cutter creates a high risk of electrocution. It certainly sounds like a risky business, but with the following precautions in place, profile cutting can be a safe and efficient way to manufacture cut metal. 

The Solutions 

Before starting any form of profile cutting, it is essential to inform any people in the vicinity that the equipment is being used so that each individual can take the necessary action to avoid harm. In industrial manufacturing, no unauthorised persons should be allowed to use a plasma cutter and it is essential that every operator undergoes appropriate training. Protective clothing and eye-wear is an absolute must for all machine operators. Goggles must provide unrestricted vision and movement while protecting the eyes from glare and debris. This means a suitably shaded, thick and unbreakable lens. Clothing must be full length to cover every inch of skin, fire resistant and without cuffs which could catch smouldering debris. It is essential to ventilate the room with fresh air or wear breathing apparatus where the fumes are likely to be intense. The risk of electrocution can be eliminated by being well grounded by wearing rubber soled boots and gloves as well as the standard welding gloves. There also must be no moisture or water around which could conduct electricity throughout the room. Finally, ensure that the plasma cutting machinery is placed as far from surrounding objects as possible to avoid sparks leaping to any material that could act as a fuel for fire.

In the workplace, the employer must ensure that these regulations are upheld to the highest standards to guarantee staff safety. At home, the individual is responsible for their health and ultimately their life, so such hazardous metalwork should not be undertaken lightly.

 Sent to us by Dan Oztunc

This article was written by Emily Banham on behalf of Kerf Developments Ltd, the leading British supplier of profile cutting, oxy-fuel cutting, high definition plasma cutting and waterjet cutting equitment. More information on plasma cutters can be found on the following link – http://www.kerfdevelopments.com/plasmacutting.html

Back Safety, Ergonomics, Fall Safety, First Aid Safety, General Safety Issues, Hand Protection, Head Protection, Hearing Protection

SAFE LIFTING OPERATIONS (GUEST POST)

Sent by Jason of Riskatmedia.com

All work activities carry the potential to cause harm to our own and others’ health and well-being, but we sometimes forget how real and close to us these hazards are.  Every year, a large number of people are killed at work, and an even greater number of people suffer work related injuries because they are unable to follow safe working practices. There are particular hazards associated with lifting operations, some of these hazards accompany almost all types of work activity, such as manual handling and slips and trips.  Others, such as contact with moving or falling objects and contact with moving machinery, are of particular concern to personnel involved in lifting operations as they result in a significant number of fatal and serious injuries each year.  In fact, contact with moving or falling objects is the third greatest cause of workplace fatality and the second greatest cause of major accidents at work. 

Manual Handling

Manual handling related activities are a major cause of occupational injury.  Low back pain, joint injuries and repetitive strain injuries of various sorts, affect over a million people each year, and many of these injuries are the result of manual handling. Prior to carrying out any unavoidable manual handling activity you should help to protect yourself from injury by following good manual handling practices.  Consider the task to be carried out and the nature of the load, and be aware of your own capabilities and the environment in which you are working. In particular, lifting accessories, lifted equipment and loads can be extremely heavy and you should give consideration to safe manual handling practices before undertaking any job that involves lifting these items. 

Slips, Trips and Falls

Slips and trips represent a significant cause of work related injury.  Slips and trips can result from contamination, obstacles, inappropriate footwear, reduced visibility, the environment and people’s attitudes.  Good workmanship and good housekeeping are practices that can help to prevent accidents and fires.  By removing waste materials to waste skips you can contribute significantly to good housekeeping.  You can also reduce the risk of slips and trips by properly routing any cables or hoses that you use, by ensuring that a safe place of work is, by ensuring that you always wear appropriate footwear, by considering whether the environment in which you will be working increases the risk of slips and trips and by taking responsibility for your own and your colleagues safety and appropriately containing any spills that you might discover.  Spills involving oil or hydraulic fluids represent a significant hazard, as they present a dangerous slip hazard and also involve substances that are both hazardous and flammable.  It is extremely important that your work area is kept clear of slip and trip hazards during lifting operations, when your own and your colleagues attention will be quite rightly focused on the lifting task at hand. 

Contact Risk

Contact with moving or falling objects is a significant hazard to personnel involved in lifting operations, as well as to personnel working close by, and can result in death or serious injury.  It is therefore vitally important that safe working practices are followed at all times during lifting operations to ensure that loads do not move, swing or fall.  

Training and Approval

All personnel need appropriate training and experience to be able to use work equipment safely.  Never use lifting equipment unless you have received suitable training and are qualified and competent to do so.  You should ensure that you are suitably qualified, competent and, where appropriate, have the necessary certifications to use the particular type of equipment that you will be working on.  All lifting operations should be controlled by an appointed, competent person who should brief all team members before the lifting operation is undertaken. 

The Lift Plan

To reduce the risk of loads moving or falling, all lifts should be planned.  Frequent or routine lifts may be subject to a generic lift plan, supported by an onsite risk assessment and team briefing.  For complex lifts, an individual and detailed lift plan should be documented.  All lift plans should be reviewed and approved by the appointed, competent person.  In particular, lifts should be planned so that personnel will not be standing or working directly beneath a load and so that the load will not be moved directly over people.  The lift plan should also provide an escape route in the event of unexpected movement of equipment or of the load. 

Suitable and Safe Equipment

It is important to ensure that all equipment used during lifting operations is safe and suitable for the job at hand.  Lifting equipment should be subjected to a detailed and thorough examination by a competent person prior to its first use on site, upon installation, when it has been disassembled and reassembled at a new location, if it has been involved in an incident, if it has been overloaded, if it has been subject to modification or major repair to safety critical components, if there have been changes in the condition of its use such as periods out of service, and for equipment used to lift personnel.  If you have any reason to doubt that such an examination has been carried out, do not use the equipment and report to your manager.  In addition, all items of electrical equipment should carry a valid appliance test certificate or label, to reduce the risk of electric shock.  Electric shock can result in death or severe burns. Serious injury can also result if someone falls or becomes incapacitated during lifting operations as a result of electric shock.  Testing should be carried out by suitably trained individuals.   You should also carry out a visual pre-use inspection of all equipment to ensure that it remains undamaged and ensure that all safety devices are fitted and are operational.  If any item of electrical equipment does not carry a valid test label, it should not be used and you should inform your manager. 

Load Integrity and Stability

Establishing load integrity and stability is also essential to reducing the risk of loads swinging, moving or falling during lifting.  All equipment operators and users should be familiar with the safe lifting capacity of the equipment and should understand the effects of changes in configuration.  The safe working load of the lifting system should be assessed, taking into account the configuration of the equipment and the operating environment where appropriate.  This safe working load should never be exceeded.  The load should possess sufficient integrity to withstand the forces applied during lifting and the method of rigging should ensure that the load remains stable and cannot tip, slip, swing or fall unintentionally.  For this reason, all rigging and thorough daily pre-use inspections should be carried out by competent personnel.  During jacking operations a firm level base should be provided against the load so that no sideways forces are present.  Loads should also be checked in increments to prevent the limit of the jack stroke from being reached. 

Human Factors

To reduce to risk of injury to other personnel from swinging, moving or falling loads, all non-essential personnel should be excluded from the area in which lifting operations are taking place.  Barriers and warning signs should be used where appropriate to facilitate this, especially as people can make mistakes and may break the rules.  These and other human factors play a significant role in safe lifting. Personnel should not undertake more than one task at a time during lifting operations and you should not take part in lifting operations if you are tired or otherwise unable to give your full attention to the task at hand. You should never come to work in possession of, or under the influence of, alcohol or drugs.  These substances expose everyone on site to risks that are unnecessary and easily avoided. 

Communication

Communication is a vital part of safe working practices during lifting operations.  The lifting appliance operator needs to be able to understand and obey an emergency stop signal no matter who gives it, and any member of the lifting team needs to be able to issue an emergency stop signal.  It is therefore vital that all members of the lift team establish, test and understand the verbal, hand signal or radio communications that will be used during the lift, prior to lifting. 

Personal Protective Equipment PPE

Personal Protective Equipment, or PPE, is an important means of reducing the risks associated with lifting operations.  At least standard PPE with safety glasses, a hard hat and industrial work gloves should be worn.  Only PPE in good working condition will reduce the hazards associated with your work, so it is important to remove, clean and store your PPE correctly.

Noise at Work

Hearing loss caused by exposure to noise at work is a significant source of occupational disease, with many people suffering deafness, tinnitus or other ear conditions as a result of exposure to excessive noise levels at work.  The level of noise and how long people are exposed to noise at work both contribute to potential hearing damage.  Noise can be reduced to harmless levels by using ear plugs and ear defenders in high noise areas. 

Emergency Procedures

In the event of an emergency while conducting lifting operations, lower any suspended loads, isolate any equipment that you have been using, make your work area safe and evacuate the area according to the site emergency procedures.  If you are involved in an accident, seek immediate assistance.  Lifting operations should never be carried out alone. 

Riskatmedia – Safety Videos

Eye Protection, General Safety Issues, Hand Protection

FOUR PREVENTIVE MEASURES YOU CAN TAKE TO PROPERLY MAINTAIN YOUR SEWER LINES (GUEST POST)

(This is an area where you don’t want to risk surprises)

Not every part of life is pretty. We don’t really want to think about our sewers that often, but like Mike Rowe displays in his popular Discovery Show Series, Dirty Jobs, there are a lot of “Hardworking men and women who earn an honest living doing the kinds of jobs that make civilized life possible for the rest of us.” Plumbers have one of those jobs, perhaps not that glamorous but if you are ever in a sewer emergency, they suddenly do become super heroes; from Upstate New York to Phoenix, Arizona, no matter if you are a stock broker or a homemaker, we all need a good, friendly neighborhood plumber from time to time. There are a couple of steps that you can take and preventive measures that you can keep in mind to help properly maintain your sewer lines.

Here are a few super tips and preventive measures that you can take so that you don’t end up with a filthy job yourself.

1). Don’t believe everything you read! When a product states that it is flushable it is not always true. The label can’t take into consideration the age or condition of your particular sewer lines. Some older and fragile sewer lines may not be able to tolerate flushing the product that you hold in your hands so when in doubt throw it out, instead of flushing it down.

2). When it comes to your sewers the two words to remember are “preventive maintenance.” Be aware of the condition of your sewer lines and don’t wait for something to go wrong before you take action. This will help you avoid possible issues later on down the road. One good suggestion, especially if you own an older home, is to have an annual inspection of your sewer lines. The plumbing industry has integrated new technology into its practices and many companies now have video cameras that they can use to scope your sewer pipes to evaluate their current condition. This is also highly recommended before a new home purchase.

3). Be aware of the placement of your landscaping. Do not plant a tree near a sewer or water line that runs through the yard. Tree and plant roots can infiltrate a sewer line and cause serious problems down the road.  You will avoid having problems later on as the trees roots can infiltrate a sewer line. In fact, roots and grease are the two main culprits when it comes to sewer line problems.

4). It is often more convenient to just flush something away then to dispose of it properly. But it is very important to remember to not use your toilet as garbage can. By not flushing the wrong types of debris down your toilet you will save water and perhaps even the cost of a plumber. Watch small children around the toilet as they love to watch many thing go “down the toilet” ie; toys, tooth and hair brushes, your keys!

Keep these 4 helpful hints in mind and they will help you keep this dirty, but necessary part of life clean and working properly. The good thing about plumbing tips is even if you live in Glendale in the Southwest of Arizona or Washington D.C., plumbing tips are pretty universal so we can all benefit from the same information and apply it so that we don’t wake up to a sewer emergency. If you would like to read about 5 things you should NOT put down your drains, click here.

Our thanks to Stephanie Drescher, who sent this very important information that affects us all.  In case you do wind up doing some plumbing yourself, be sure to wear gloves and safety glasses and any other protection you may need.  We all should appreciate our plumbers, who do jobs we don’t want to do, but receive good compensation for their hard work. pb

 

Eye Protection, First Aid Safety, General Safety Issues, Hand Protection, Head Protection, Hearing Protection, Respiratory Safety

THINGS YOU MAY NOT KNOW ABOUT TRAINS, PART I

Have you ever wondered as you drive down the highway about those trains you see rolling along, and what on earth could be in all those cars?  You also see lots of graffiti, done by some local “artists” along the way, and can’t help but question all the places that train has been.  One thing you need to understand, is that many of those cars are carrying hazardous materials, and in the event of a derailment, or spill, you need to drive away from the area as soon as possible. 

Railroad companies are overseen primarily by the Federal Railroad Administration, but also answer to the Department of Transportation, and the National Transportation Safety Board.  No person may transport a hazardous material in commerce unless that material is properly classed, described, packaged, marked, labeled, and placarded and is in condition for transportation according to DOT regulations.  Railroad Company computers are able to track the trains at all times. 

For your information, here are the hazard classes and divisions:

  • 1 – Explosives (1.1 – Explosive with mass explosion hazard; 1.2 – Explosive with projection hazard; 1.3 – Explosive with predominantly fire hazard; 1.4 – Explosive with no significant blast hazard; 1.5 – Very insensitive explosive; blasting agent, and 1.6 – Extremely insensitive detonating substance.)
  • 2. – Gases (2.1 – Flammable gas; 2.2 – Nonflammable, nonpoisonous, (nontoxic), compressed gas; and 2.3 – Poisonous (toxic) gas (by inhalation).
  • 3 – Flammable Liquids
  • 4 – Flammable Solids and Reactive Solids/Liquids (4.1 – Flammable solid; 4.2 – Spontaneously combustible material, and 4.3 – Dangerous when wet marked.)
  • 5 – Oxidizers and Organic Peroxides  (5.1 – Oxidizer; 5.2 Organic peroxide.)
  • 6 – Poisonous (Toxic) Materials/Infectious Substances (6.1 – Poisonous (Toxic) material; 6.2 – Infectious substance.
  • 7 – Radioactive Materials
  • 8 – Corrosive Materials
  • 9 – Miscellaneous Hazardous Materials

Worded Classes

Combustible Liquids (regulated in bulk packaging only)

ORM-D (Other Regulated Materials – D) (regulated in air transportation only; not regulated in rail transportation. 

Shipping hazardous materials are time-sensitive.  Those under a 20-day time limit to arrive are:

  • 1.      Ethylene, refrigerated liquid
  • 2.      Hydrogen, refrigerated liquid
  • 3.      Chloroprene, stabilized
  • 4.      Flammable liquid, N.O.S.
  • 5.      Hydrogen chloride, refrigerated liquid
  • 6.      Vinyl fluoride, stabilized

Those having a 30-day shipping limit are:

  1. Styrene monomer, inhibited
  2. Flammable Liquid, (Recycled styrene) 

When transporting hazardous material shipments in a train, a member of the train crew must also have acceptable emergency response information and a document showing the current position of each hazardous material in the train.  This documentation provides railroad and emergency response personnel with accurate information for every hazardous material being transported. 

Next, In Part II, we will talk about what type of training railroad crews experience to be prepared for a hazardous material spill caused by a railroad derailment or railroad car leak.  Please read on…..

Source: Daniel Burlison, Retired Manager, Train Operations