Tag Archives: safety guidelines

TOP TEN FORKLIFT FAUX PAS – HOW COMPANIES ARE AVOIDING FATAL ACCIDENTS (GUEST POST)

No matter what industry you’re in; oil and gas, shipping and receiving, warehouse or construction, there is one common factor that business owners, including myself, have a difficult time dealing with… workplace accidents! In particular, forklift accidents. It’s easy to blame it on inadequate forklift maintenance or even a freak accident but in the world of business there shouldn’t be these types of errors. A typical forklift
accident is usually the fault of who’s operating it. Take a look below to find the most common operator errors!

Top 10 Common Forklift Faux Pas

• Traveling too fast – speeding
• Operating with elevated loads
• Erratic jerking while driving
• No communication with staff
• Hitching a ride or giving a ride
• Inadequate breaking, turning and backing
• Improper parking
• Blocking railway car/semi-trailer wheels
• Horseplay
• Intoxication

How to Lower These Risks

It’s important that you and your staff are on the same page.  If you have a few bad apples this can trickle down hurting your bottom line. To ensure proper safety and employee compliance, get rid the operators that are not following the safety guidelines and properly train a select few to carry on with business.

When I started to grow my online retail store I never thought it would blossom into what it has today. After 3 years I expanded largely and needed a warehouse where I can ship and receive goods. After one of my workers received a debilitating injury I vowed it would NEVER happen again! I decided to sit down with my staff and get down to the important stuff. My first question was “what can I do to make your job safer?” 

With a great deal of hands rising up I was shocked to see such an immediate and persistent response. The first answer I received was more training! I was a bit surprised since I had assumed that if I hired a package handler they knew how to handle packages and if I hired a forklift operator he knew how to operate a forklift! I also posted general safety guidelines throughout the warehouse assuming that would be enough. I was wrong! Since these men and women came from different situations I needed to gather them together and get everyone thinking about safety first! 

I set up mandatory weekly safety training meetings where we would discuss possible risks, watch forklift training videos and go over any areas of the warehouse that needed tending to. The overcrowded aisles became a hazard and dealing with those issues has helped tremendously! It’s important to properly train your employees the way you want them trained, never assume they know how you want your operation ran!

Author Bio – Sarah Shade is a research assistant for safetyvideos.com, she researches the latest in industrial news and brings her readers helpful information.

OSHA AND ELECTRICITY: KEEPING THE FACTORY FLOOR SAFE (GUEST POST)

Sent to us by Maire Hunter.

The Occupational Safety and Health Administration sets regulations to ensure employees’ safety. These requirements apply to all industries, especially construction and factory work.

In addition to an employer following safety guidelines, employees working on or around electrical equipment should have safety training. OSHA regulations align with the standards set by the National Fire Protection Association in NFPA 70E.

General OSHA regulations for electrical use in any industry

  • Electrical cords may not be modified.
  • Ground prongs can’t be removed from any cord or plug.
  • Extension cords must have three wires, one wire being grounded.
  • Cords, fittings and connections must have a strain relief.
  • Shut-offs or disconnects must be clearly identified on all equipment.
  • All electrical equipment must be inspected before use. Defective equipment must be taken out of service.
  • Ground-Fault Circuit Interrupters (GFCI) must be used in typically wet locations.

Requirements for wiring and safe operation

  • All electrical wire, equipment and conduit must be approved by either Underwriters Laboratories (UL) or Factory Mutual Corporation (FMC).
  • When energized equipment or lines are exposed, effective barriers or temporary fencing must be used.
  • High-voltage equipment (600 volts or more) must be isolated.
  • Temporary wiring, used during construction, remodeling or repairs, must meet National Electrical Code (NEC) requirements.
  • Temporary wiring must be removed immediately after the work is completed.
  • Exposed electrical wires must be protected.

When it comes to protecting electrical wires, a metal or plastic conduit is the best choice. Conduit materials include aluminum, cast zinc, galvanized steel, steel and PVC.

Partial list of conduit requirements

  • Any wiring installed in a conduit must be protected by bushings at the end of the conduit.
  • Liquid tight conduit and weatherproof connections must be used in outdoor locations.
  • The NEC has regulations for the maximum number of wires allowed in any given conduit. The number of wires depends on the diameter, American Wire Gauge and type of wire.
  • Most metal conduits can be used as equipment ground conductors. Plastic conduits must have a separate ground conductor. The ground conductor must also be identified.
  • Spacing between conduits is required for safe access during repair work.

Normally, if an accident occurs, OSHA will become involved and may conduct safety assessments. In addition to OSHA guidelines, the NEC applies to all construction work and all commercial electrical use. Compliance with NEC requirements is normally checked during stages of building inspection. Insurance companies may require further inspection for compliance.

Following the guidelines set by OSHA will help protect the health and safety of employees. A reduction in accidents may reduce insurance rates and will reduce lost time from work. While ignoring regulations may not result in an accident, the potential fines levied by OSHA can be significant.

All workers who work around electricity should be furnished dielectric personal protective equipment, such as dielectric glasses and gloves. pb